Luminex 100 IS User Manual, Version 2.3 User Manual Page 189
- Page / 228
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
xMAP Technology Luminex 100 IS System Setup
PN 89-00002-00-071 Rev. C B - 7
3. Unscrew the cap from the Cheminert fitting.
4. Insert the sample probe into the sample probe holder. Insert the
Cheminert fitting into the sample probe holder, turning it
clockwise. Be careful that the threads are correctly aligned. Hand
tighten only. See Figure B-7.
Figure B-7 Insert Sample Probe and Cheminert Fitting
5. Push the light housing back into place.
6. Install the clear plastic shield that covers the sample probe area.
See Figure B-8.
Figure B-8 Sample Probe Area with Clear Plastic Shield in Place
1. Cheminert Fitting 3. Sample Probe
2. Sample Probe Holder
1
3
2
- Luminex 100 1
- User Manual Version 2.3 1
- EULA PN: 89-30000-00-070 6
- Contents 7
- Basic Concepts 4-1 8
- PN 89-00002-00-071 Rev. C v 11
- Maintenance and Cleaning 6-1 12
- Troubleshooting 7-1 12
- Product Numbers 8-1 13
- Glossary A-1 13
- Output.CSV C-1 14
- Index Index-1 14
- Introduction 15
- Figure 2-2 CE Label 19
- Figure 2-7 Laser Class Label 22
- Mechanical 23
- Biological 23
- Blue Indicator Light 24
- Decontaminating 25
- Analyzer for Return 25
- Shipment 25
- The System 27
- Analyzer General 31
- Luminex XYP 32
- Instrument General 32
- Recommended Additional 33
- Equipment 33
- Electronics 33
- Fluidics 34
- Figure 3-4 Air Intake Filter 36
- Air, Waste, and 37
- Sheath Fluid 37
- Connectors 37
- Reagents 38
- Basic Concepts 39
- 3. Command List 48
- Acquisition Detail 54
- 4. Acquisition Detail Toolbar 55
- 1. Replay Batch 6. Cancel All 56
- 3. View Batch Data 8. Pause 56
- 4. Start Plate 9. Resume 56
- 5. Cancel Command 56
- Disconnected 61
- Secondary 62
- Replicate 71
- Averaging 71
- Define General 81
- Tab Information 81
- Define Company 82
- Information Tab 82
- Define Data Export 83
- Setting up the Favorites 84
- Startup Procedures 85
- To perform a Wash command: 87
- Set Luminex XYP 87
- Instrument Heater 87
- Temperature 87
- Run System xMAP 89
- Calibrators 89
- Controls 91
- Exporting CAL or 93
- CON lots 93
- Importing 94
- Templates 94
- To create a new batch: 95
- Create a Multi 100
- Open a Multi 101
- To open a multi-batch: 102
- Process Multiple 102
- To edit a patient list: 106
- Assign Sample 106
- Dilution Factors 106
- Create a New 107
- Advanced Batch 107
- Table 5-9. Symbol 109
- Color Codes 109
- Edit Lot 115
- Information on an 115
- Unused Template 115
- Export a Lot from 117
- Template 117
- Analyzing Batches and 118
- Multi-Batches 118
- Customize Data 119
- Analysis Settings 119
- Enable Automatic 124
- Analysis 124
- Running Reports and 128
- Analyses 128
- Print Data 131
- Analysis Report 131
- Database Management 132
- Procedures 132
- Recommended Use Schedule 134
- To perform a disk cleanup: 137
- Daily Shutdown 138
- Maintenance and Cleaning 141
- Routine Tasks 142
- Note: There is NO warning of 143
- Clean the Sample Probe 144
- Every Six Months 145
- Luminex XYP Instrument 146
- Air Intake Filter 146
- 1. Syringe Seal 2. Syringe 148
- Luminex 100 Analyzer 149
- Ventilation Filter 149
- Annually 150
- As required 151
- Maintenance Log 153
- Troubleshooting 155
- Power Supply 156
- Problems 156
- Calibration and 161
- Control Problems 161
- Acquisition 163
- Bead Detail 164
- Irregularities 164
- Figure 7-2 Normal Histogram 165
- View a list of incompatible 166
- Technical Support website 166
- System Error 167
- Messages 167
- Sample Error 169
- ± 3.0. If 171
- Luminex SD 172
- 16. Run four WASH commands 174
- Product Numbers 175
- Software 177
- Training 177
- Glossary 179
- Luminex 100 IS 183
- System Setup 183
- 1. Monitor 4. Barcode Scanner 184
- 2. PC 5. Luminex SD system 184
- Connect the Luminex 100 185
- XYP to the PC 185
- Install the Luminex XYP 188
- Instrument Sample Probe 188
- Instrument Reservoir 191
- Calibrate and Verify the 192
- Instrument Heater Block 195
- Luminex 100 IS 2.3 196
- Installation 196
- Luminex 100 Version 1.7 197
- Version 2.3 197
- Verify Successful 198
- Remove Luminex 200
- 100 Version 1.7 200
- Luminex 100 IS Version 201
- 2.1/2.2 to Luminex 100 IS 201
- 100 IS 2.1 or 2.2 202
- Install Luminex 202
- 100 IS 2.3 202
- Firmware 203
- Firmware Upgrade 204
- Verify Successful 205
- Update Interface 205
- Firmware Update 206
- Luminex SD System 207
- Network Installation 208
- Advisory 208
- Prepare System for 208
- First Use 208
- Installation Drawing 209
- Output.CSV 211
- Field Definitions 212
- Statistic Description 214
- Statistics Column 215
- Definitions 215
- Column Name Description 216
Related products and manuals for Equipment Luminex 100 IS User Manual, Version 2.3
(270 pages)
Equipment Luminex IS Version 2.3 User Manual
(120 pages)
(120 pages)
Equipment Luminex IS Version 2.3 User Manual
(140 pages)
(140 pages)
© 2020, manymanuals.com. All rights reserved. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals